MB SpeedStop MB/BMW/Renault Filter  - the filter with Speed Stop function for Mercedes. 

For installing into the EZS or Cluster, CAS4/FEM/BDC, is intended for mounting on Renault, Mercedes and BMW F-serie vehicles CAN bus, with EZS/CAS4/FEM/BDC modules maked on NEC и FREESCALE microcontrollers.

Have all functions of filter 1615 (MB/BMW/Renault)
+ function of make slow or stop Main Mileage counter for clusters W205/W222/W213 '2013...2018 years.

 

Production date of filter "1715" since 10.2017 year.

There is  two versions of filter:

1 - This device is "Plug and Play", for the installing into the plug of Cluster W205, W222. Not applicable for W213 (it have another connector).

 

2. Device for soldering into EZS or Cluster modules. Applicable for all cars W205, W222, W213.

 

The SpeedStop function work well in most of Mercedes W205, W222, W213 and similar cars, where was installed such clusters. 

For W213, filter must be installed permanently, because without filter the big (proper) km value will be returned back on the cluster display.

The filter must be installed into the EZS or into the Cluster, into the broken CAN bus between the Cluster and EZS modules.

 

For W205/W222:  Slows (stops) the Arrow and Counter. 
Installation is fully same as installed "Main Filter" 161x (see connection pictures in archive).

Control of filter - by the buttons of left panel on the steering wheel.

- Two count modes "Count /2" and "Count Stop", cyclic switching between modes by the button HOME(OK) holding more 2sec
    Count /2 = 2 flashes of FarLight lamp on the cluster
    Count Stop = 3 flashes of FarLight lamp on the cluster
- Switch OFF (usual count) with button ESCape, hold more than 2sec ( 1 flash of FarLight lamp on the cluster).

- Switch OFF FOREVER of function SpeedStop - if the user of car deside to sold this car:
  press and hold both buttons HOME(OK) and ESCape more than 5 sec ( 5 flashes of FarLight lamp on the cluster).

  After permanent blocking of SpeedStop function, new activation of SpeedStop is possible only by the "Unlock" of filter with MBcleaner tool.

   

 

 

For W213Slows (stops) the Counter only, the Arrow keep work as well!

The picture for filter(s) connection into EZS IS HERE.

Caution. In W213, the EZS is too smart, it can count the mileage by itself. That's because the unmounting of filter causes jump back of right mileage to the cluster from EZS. Please don't unmount the filter, better just deactivate it as described above.

For the "proper" reading of mileage data from EZS W213 via OBD diag.tools, you need to install second filter "OBD filter".
Please refer to the connection picture for W213 above.
For this purpose you can use the regular filter 1615, 1616, 1617 with last firmware inside.

 

Because the W213 cars may be equipped differrently, the 2 versions of control present for this filter 1617.
One of them can work for your car.

Version 1: Control by the buttons of right wheel panel:

- Two count modes "Count /2" and "Count Stop", cyclic switching between modes by the quad sensor button [OK] holding more 2sec
    Count /2 = 2 flashes of FarLight lamp on the cluster
    Count Stop = 3 flashes of FarLight lamp on the cluster
- Switch OFF (usual count) with button HOME, hold more than 2sec ( 1 flash of FarLight lamp on the cluster).

Switch OFF FOREVER of function SpeedStop - if the user of car deside to sold this car:
  press and hold both buttons quad [OK] and HOME more than 5 sec ( 5 flashes of FarLight lamp on the cluster)

   After permanent blocking of SpeedStop function, new activation of SpeedStop is possible only by the "Unlock" of filter with MBcleaner tool.

 

Version 2: Control by the Home buttons of right and left panels:

- Two count modes "Count /2" and "Count Stop", cyclic switching between modes by the Right Home button holding more 2sec
    Count /2 = 2 flashes of FarLight lamp on the cluster
    Count Stop = 3 flashes of FarLight lamp on the cluster
- Switch OFF (usual count) with button Left HOME, hold more than 2sec ( 1 flash of FarLight lamp on the cluster).

Switch OFF FOREVER of function SpeedStop - if the user of car deside to sold this car:  press and hold both buttons Left and Right HOME more than 5 sec ( 5 flashes of FarLight lamp on the cluster)

  After permanent blocking of SpeedStop function, new activation of SpeedStop is possible only by the "Unlock" of filter with MBcleaner tool.

 

 

 

Version 3 (2017-18 restyling) for filters sold (version) before 2018.12.02:

Control by 2 buttons of left panel of wheel:

- Two count modes "Count /2" and "Count Stop", cyclic switching between modes by the holding of button HOME more 2sec
    Count /2 = 2 flashes of FarLight lamp on the cluster
    Count Stop = 3 flashes of FarLight lamp on the cluster
- Switch OFF (usual count) with button ESC, hold more than 2sec ( 1 flash of FarLight lamp on the cluster).

Switch OFF FOREVER of function SpeedStop - if the user of car deside to sold this car:
  press and hold both buttons quad ESC and HOME more than 5 sec ( 5 flashes of FarLight lamp on the cluster)

  After permanent blocking of SpeedStop function, new activation of SpeedStop is possible only by the "Unlock" of filter with MBcleaner tool.

        

 

Version 4 (2017-18 restyling)  for filters sold (version) after 2018.12.02:

Control by one button "ESC" ( or "HOME", it depends by style of the buttons panel) of left panel of wheel:

- Three count modes "Count /2", "Count Stop" and "Normal Count", cyclic switching between modes by the holding of button "ESC" (or "HOME") more 2sec
    Count /2 = 2 flashes of FarLight lamp on the cluster
    Count Stop = 3 flashes of FarLight lamp 
    Switch OFF (usual count) = 1 flash of FarLight lamp.

Switch OFF FOREVER of function SpeedStop - if the user of car deside to sold this car:
  press and hold both button "ESC" (or "HOME") more than 10sec ( 5 flashes of FarLight lamp on the cluster)

  After permanent blocking of SpeedStop function, new activation of SpeedStop is possible only by the "Unlock" of filter with MBcleaner tool.

 

Connection "inside EZS".

     1. Find number on a Filter board, find a photo with the necessary Filter connection pictures. 

     2. Desolder (remove) the ferrite CAN noise filter from a EZS board.

             Be careful: EZS has more than one such fnoise filter! You must remove only one that is shown on a connection photo!!!

     3. Find visually on a connection photo the connection points of ground and power supply wires.

     4. Important: First wire to soldering is ALWAYS GROUND wire! 

             It will be do always to Electrostatic Discharge prevent.

     5. After ground wire soldering you can solder CANs wires and power supply wire.

             Be careful:  On some (similar at first look) Filter connection pictures, the CAN1 and CAN2 wires pairs can have different connection !!! 

 

Please correctly select pictures and the Filter connections!